EdgeSwitch X 1.11.1 includes the below bugfixes and improvements.

Improvements

• Web Interface - Added Multicast Group table for better monitoring of multicast behavior.
• Flood ND group option was added into MLD Snooping.
• Added IPv6 MLD querier.
• SNTP Client now supports IPv6 address.

Bugfixes

• Port with disabled STP was reporting a forwarding state.
• IGMP snooping was not working if IGMPv3 join packet contains a reserved address.
• IGMP snooping querier IP was not set properly.
• Port mirror was not blocking ingress traffic until restart.
• Rename the default VLAN is now allowed.

Known issues

This version is not compatible with password generator used in UISP Application older than 2.4.126.

EdgeSwitch X 1.10.2 includes the below bugfixes and improvements.

Improvements

• Upgraded the SSH Server.

Bugfixes

• Disabled weak SHA1 SSH ciphers.
• Disabled weak SHA1 HTTPS ciphers.

Known issues

This version is not compatible with password generator used in UISP Application older than 2.4.126.

EdgeSwitch X 1.10.1 includes the below bugfixes and improvements.

Improvements

• Added Storm Control support.
• Added Port Mirroring.
• Upgraded the SSH server.
• DHCP snooping configuration on LAG interfaces in mobile apps.
• Speed up port trunk configuration.

Bugfixes

• Fixed bug when STP discarding state was not visible on ports in LAG.
• Fixed possible CLI crash during listing a log.

Known issues

This version is not compatible with password generator used in UISP Application older than 2.4.126.

EdgeSwitch X 1.9.0 includes the below bugfixes and improvements.

Improvements

• Updated Local Web Interface with various fixes and improvements:
• Tooltips are not displayed correctly in some situations.
• Fixed bug when username can not be changed in some situations.
• A strong password is now required for newly created passwords.
• Upgraded the SSH server.
• Updated Web Server SSL cipher list.

Known issues

This version is not compatible with password generator used in UISP Application older than 2.4.126.

EdgeSwitch X 1.8.1 includes the below bugfixes and improvements.

Improvements

• Updated Local Web Interface with various fixes and improvements.
• Added possibility to change username.
• Changed minimum password length to 12 for newly created passwords.
• Updated UISP Application connector.
• Speed up configuring address when SLAAC is being enabled.
• Speed up booting time when static IP is configured.
• Renew DHCP address if management VLAN is changed.

Bugfixes

• Fixed errors when trying to set half-duplex speeds on LAG ports.
• Fixed bug when disabled remote syslog was enabled again after reboot.
• Fixed bug when remote syslog settings was changed only after reboot.
• Fixed an issue that System log is disabled after backup restore.
• Fixed bug when jumbo frame does not work without reboot.

EdgeSwitch X 1.5.2 includes the below bugfixes and improvements.

Improvements

• Optimized STP to lower the CPU load.

Bugfixes

• Fixed issue when factory-reset sometimes doesn't reset PoE status.

• Added CLI access via UISP Controller (requires UISP v1.4.5 or newer).
• Optimized speed of generating of the support file.

Bugfixes

• Fixed various security fixes in OpenSSL and zlib libraries.
• Fixed newly discovered out-of-bound reads in crafted LLDP packets.
• Fixed system LED indication failing after some time.
• Fixed "Could not chdir to home directory" message on SSH login.
• Fix loss of address from DHCP with short DHCP lease times.

• Fixed newly discovered out-of-bound reads in crafted LLDP packets.
• Fixed various security fixes in OpenSSL and zlib libraries.
• Fixed system LED indication failing after some time.
• Fixed "Could not chdir to home directory" message on SSH login.

New firmware for EdgeSwitch X product line, improving UISP integration and fixing several issues. Use UISP 1.4.2 or newer for best compatibility.

Improvements

• Added support for showing port STP state in UISP.
• Improved compatibility with UISP v1.4.0 and newer.
• Default device name is based on device's MAC address.

Bugfixes

• Fixed race condition in configuration restore state.
• Fixed possible out-of-bounds read in crafted LLDP packets

This upgrade fixes issue with upgrading of ES-18X to v1.3.x firmware reported for the v1.3.0 release and fixes potential security vulnerability in LLDP packet handling.

Bugfixes

• Fixed upgrade of ES-18X v1.2.x to firmware v1.3.x.
• Fixed potential vulnerability via crafted LLDP packets.

• Added SNMP configuration to web UI.
• Trunk mode is no longer enabled on all ports in default configuration.
• Discovery scanner configuration options have been removed, scan is now performed only when neighbors are requested.
• Improved detection of client information (IP address and hostname) in MAC table.
• Changed color scheme of the web UI.

Bugfixes

• Fixed SNMP stopping to reply and utilizing 100 % CPU.
• Some marginal MIBs removed to increase SNMP stability and responsiveness.
• Fixed device sometimes not replying to discovery requests.
• Fixed incorrect speed reported in SNMP when port is down.
• Other minor fixes improving UNMS compatibility and stability.
• Fixed incorrect device name reported in SNMP.
• Fixed high CPU utilization with plugged SFP modules.
• Fixed possible deadlock when processing HTTP requests.

Known issues

Firmware v1.2.x on ES-18X fails to upgrade to v1.3.0. This will be fixed in v1.3.1.

This release adds option for trunking undefined VLANs. If enabled, trunk ports will also carry traffic from VLANs that are not defined in the list of VLANs and exclude traffic only from VLANs explicitly excluded. This behavior is default for EdgeSwitch XP trunk ports and this options brings feature parity for VLAN configuration to EdgeSwitch X line. Although the feature has been tested, use it with caution.

Optional device statistics and stability reporting is present since v1.2.0, which is disabled by default. A prompt for enabling this feature is shown after logging into the web interface. When enabled, it can be turned off at any time in the Device Reporting section of the System Settings.

Improvements

• Increased resistance of web UI to XSS and clickjacking attacks.

Bugfixes

• Set correct MTU when disabling jumbo frames.

Version v1.1.5 is the last security release of 1.1.x line of EdgeSwitch X firmwares. For continued support and security fixes, please migrate to EdgeSwitch X firmware v1.2.3 or newer.

Improvements

• Increased resistance of web UI to XSS and clickjacking attacks.

This release adds option for trunking undefined VLANs. If enabled, trunk ports will also carry traffic from VLANs that are not defined in the list of VLANs and exclude traffic only from VLANs explicitly excluded. This behavior is default for EdgeSwitch XP trunk ports and this options brings feature parity for VLAN configuration to EdgeSwitch X line. Although the feature has been tested, use it with caution.

Optional device statistics and stability reporting is present since v1.2.0, which is disabled by default. A prompt for enabling this feature is shown after logging into the web interface. When enabled, it can be turned off at any time in the Device Reporting section of the System Settings.

New features

• [System] Added device analytics ID and example output to tech-support file.

Bugfixes

• [VLAN] Fixed error when changing VLAN configuration of LAG interfaces.
• [GUI] Fixed overflow of received bytes in Web UI.

This release adds option for trunking undefined VLANs. If enabled, trunk ports will also carry traffic from VLANs that are not defined in the list of VLANs and exclude traffic only from VLANs explicitly excluded. This behavior is default for EdgeSwitch XP trunk ports and this options brings feature parity for VLAN configuration to EdgeSwitch X line. Although the feature has been tested, use it with caution.

Optional device statistics and stability reporting is present since v1.2.0, which is disabled by default. A prompt for enabling this feature is shown after logging into the web interface. When enabled, it can be turned off at any time in the Device Reporting section of the System Settings.

Bugfixes

• Fixed losing of untagged status on non-trunk ports excluded from VLAN 1.
• Fixed HTTPS certificate/SSH key always regenerated after backup restore.

This release adds option for trunking undefined VLANs. If enabled, trunk ports will also carry traffic from VLANs that are not defined in the list of VLANs and exclude traffic only from VLANs explicitly excluded. This behavior is default for EdgeSwitch XP trunk ports and this options brings feature parity for VLAN configuration to EdgeSwitch X line. Although the feature has been tested, use it with caution.

Optional device statistics and stability reporting has been added to v1.2.0, which is disabled by default. A prompt for enabling this feature is shown after logging into the web interface. When enabled, it can be turned off at any time in the Device Reporting section of the System Settings.

New features

• Added option for trunking undefined VLANs.
• Added tooltip for quick UNMS connection and diagnostics.
• Added possibility to perform factory reset using the button when device is running.
• Added statistics and stability reporting with opt-in prompt.
• Added support for ES-18X.

Improvements

• Improved support for configuration of the device using UNMS Mobile.
• Full names of discovered devices are shown in the Discovery tool.
• Added warning when enabling PoE on active ports.
• Details from LLDP and Discovery are shown in port detail tooltip.
• Improved ping tool granularity.
• STP auto edge is now the default option on switch ports.
• Changed default parameters of STP for faster convergence.
• Changed default LAG mode to LACP.
• Improved stability of UNMS connection.
• Minimum password length increased to 8 characters in UI.

Bugfixes

• Fixed restored configuration being partially applied after uploading, now it is applied completely after reboot.
• Fixed memory leak when device was connected to UNMS for long periods.
• Fixed various minor issues in the web interface.
• Fixed PoE state not cleared when runtime factory reset is performed.
• Fixed PoE losing state after reboot on ES-18X (on devices with pre-release firmware only).
• Fixed overflow in transmitted bytes port statistics.

Changes since v1.2.0-beta.1:

• Fixed tagged VLANs reverting to untagged after reboot.
• Fixed overflow in transmitted bytes port statistics.
• Fixed system LED indication of UNMS status after using quick connection dialog.
• Fixed issues with setting of IPv6 link-local address in UI.

Known issues

Ports set as excluded on VLAN 1 with port trunking unchecked are reverted from Untagged to Excluded on other VLANs.

A workaround can be toggling the trunk option for these ports - unless you have "Trunk undefined VLANs" enabled, the behavior should not be different from having the trunking disabled. This issue will be fixed in release v1.2.1.

• Fixed command injection in copy tech-support.

• Fixed another command injection in copy running-config.
• Fixed Ubiquiti Discovery over IPv6.

• Fix occasional packet loss issues.
• Fix PoE staying enabled after factory reset without power cycle.
• Fix missing values in Ubiquiti Discovery responses.